Product Information
Optimizer VAV controller, BACnet IP, 24VAC, 7 UIOs, 5SSRs, replaceable air flow sensor, integrated 44 in-lbs (5 Nm) @ 90sec actuator with analog position feedback
Specifications
Integrated Actuator SpecificationsHardware
| Parameter | Specification |
|---|
| CPU | Crossover processor NXP I.MRT, Cortex M7 |
| Memory capacity | 16MB QSPI Flash, 16MB SDRAM |
| BACnet® IP | 2 × RJ-45 ports, 10/100 Mbps with loop protection (RSTP supported). |
| BACnet® IP T1L | 2 × T1L ports with fail-safe, up to 10 Mbps, loop/daisy-chain supported. |
| Real Time Clock | 24-hour backup via supercapacitor; resets after 24h until BACnet® Time Sync. |
| Small LED | Transmission/Reception for Modbus and BACnet® (green). |
| Ring LED | Status: normal, firmware download, broken sensor (green/yellow/red). |
Integrated Actuator SpecificationsElectrical
| Parameter | Specification |
|---|
| Rated Input Voltage | 20–30 VAC; Class 2 transformer |
| BACnet® IP (CAT5/6) | Nominal: 14.53 VA; Max: 30 VA |
| BACnet® MS/TP | Nominal: 15.33 VA; Max: 22 VA |
| BACnet® IP (T1L) | Nominal: 8 VA (VA75T24NM); 6.5 VA (VA00TB24NM); Max: 25 VA / 14 VA |
| Frequency Range | 50/60 Hz |
| Internal Power Supply | Half-wave rectifier |
IMPORTANT: UL listed, limited to 100 VA maximum. Do not exceed rating.
Integrated Actuator SpecificationsSylk Supported Devices
| Wall modules | TR42, TR42-H, TR42-CO2, TR71, TR75, TR120, TR100 (emulation), TR120-H (emulation) |
| Sensors | TR40, TR40-H, TR40-CO2, TR50 (emulation), C7400S |
| Actuators | MS3103, MS3105, MS3110 (5 Nm), MS3120 (10 Nm) |
| Non-Sylk™ actuators | MS4103, MS4105, MS7403, MS7405, MS7503, MS7505, MS8103, MS8105 |
Integrated Actuator SpecificationsIntegrated Actuator Specifications
| Parameter | Specification |
|---|
| Torque | 44 in-lbs (5 Nm) |
| Run Time | 108 s @ 50 Hz; 90 s @ 60 Hz |
| Mounting Shaft | Round 8–16 mm; Square 6–13 mm |
| Shaft Length | ≥ 41 mm |
| Position Feedback via integrated potentiometer |
Solid State Relay (SSR) Specifications
SSR switches supply voltage and work with VAC and VDC. VDC switching does not support synchronous motors.
Specifications:
- 1.5 A constant; 3.5 A inrush for 0.1 sec per SSR output.
- Optional jumper between 24 VAC supply and SSR input shared by all SSRs.
Integrated Actuator SpecificationsUniversal IO (Configurable as Analog Output or Universal Input)
| AO | 0(2)–10 VDC direct/reverse with −3 mA to 20 mA or current output with 0(4)–20 mA. |
| UI | - 0(2)–10 VDC direct/reverse or 0(4)–20 mA input. Sensors: 10K Ohm NTC Type II, 10K-3 NTC, 10K3A1, 20K Ohm NTC, PT100, PT1000, NI1000TK5000, NI1000 Class B DIN43760, PT3000, 100 Ohm–100K Ohm resistive (custom characteristic). Hardwired wall modules: set point, fan speed, override.
- Dry contact binary input with direct/reverse.
- All UI can be used for pulse input. Max frequency 100 Hz; duty cycle 5 ms ON / 5 ms OFF.
|
The controller has a single common terminal for every two Universal IOs, protecting against 24 VAC miswiring and short circuits.
Integrated Actuator SpecificationsCommunication Specifications
| Parameter | Specification |
|---|
| Protocols Supported | BACnet® IP, BACnet® IP (T1L), BACnet® MS/TP, Sylk™, Modbus RTU (client only), BLE |
| Ethernet Speed | IP: 10/100 Mbps; T1L: 10 Mbps |
| IP Version | IPv4 |
| Addressing Modes | Dynamic (DHCP, Link Local); Static |
| Sylk™ Bus | 2-wire, polarity-insensitive |
| Bluetooth | BLE, optional external antenna |
Differential Pressure Sensor SpecificationsDifferential Pressure Sensor Specifications
| Parameter | Specification |
|---|
| Range | ±2.0 in WC (±500 Pa), bi-directional |
| Span Accuracy | ±3% of reading |
| Field Replaceable Sensor | Yes |
Standards and Approvals
- CE
- BACnet® Advanced Application Controller (B-AAC)
- UL916, Energy Management Equipment
- FCC Part 15, Class A
- EN 55022 Class A
- EN 61000-3-2, 61000
- Plenum Tested (UL2043)
Operational Environment SpecificationsOperational Environment Specifications
| Parameter | Specification |
|---|
| Storage Temperature | −40 °F to 150 °F (−40 °C to 66 °C) |
| Operating Temperature | 32 °F to 122 °F (0 °C to 50 °C) |
| Humidity | 5%–95% RH, non-condensing |
| Protection | IP20, NEMA 1 |
| Pollution Degree | 2 |
IP (T1L) Communication SpecificationsIP (T1L) Communication Specifications
| Parameter | Specification |
|---|
| 10BASE-T1L Standard | 802.3cg-2019 |
| Connection | Screw terminal, auto MDI-X T1L polarity detection and correction |
| Cable Type | Single twisted pair balanced, 18AWG, shielded/unshielded. CAT5/6 UTP supported (1 pair). Belden 74040NH, 9841NH or equivalent. Specs: 300 V rating, 100 Ω ±20% impedance, max resistance 22 Ω/km, capacitance 40–60 nF/km. |
| Distance | Up to 3281 ft (1000 m) depending on cable characteristics |
| Transmission Rate | 10 Mbps |
